THIN- 2:1 Two Part Thin Epoxy Resin System - Kit Size 1.5 Gallons

Ground Only

The Thin Epoxy Resin is a high quality resin system which works well for lamination of Fiberglass, Carbon Fiber or Kevlar. This epoxy has a syrup like consistency and will wet-out materials very quickly. This makes it very easy to work with. The epoxy is low odor. In addition to lamination of materials this epoxy also works very well as a sealer for porous materials such as wood, because of its ability to easily penetrate the materials. Resin viscosity: 600 cps.

This resin uses a 2:1 hardener. Mixing 2 parts epoxy to 1 part hardener will give you the appropriate final mixture.

This epoxy is NON-blushing.

This is considered to be a slow hardener, Our 3:1 and 4:1 hardener epoxies will cure much faster. However this 2:1 hardener will provide you with the maximum working time possible and should not be used in temps under 70° F unless a very long curing time is needed. Slow hardener should be used at temperatures above 80° F for optimal overnight curing.

Low viscosity and good color
Excellent toughness
Excellent flexibility

Typical physical properties for hardener systems:

Typical Properties 2:1 Slow Hardener
Viscosity at 25°C/77°F 600 cps
Color Gardener 1 max
Pounds per gallon 9.2
Mix Ratio By Volume, 100 parts resin 50
Mix Ratio By Weight, 100 parts resin 46
Gel Time at 77°F, 100 grams, minutes 40-50
Hardness, Barcol, 934-1 24-28
Heat Distortion Temperature 46-52°C / 115-125°F
Tensile Strength, psi 8-9,000
Tensile Elongation, percent 2.0 - 3.0
Flexural Strength, psi 12-14,000
Flexural Modulus, psi x 10(-5)
Water Absorption, percent by weight
5.0 - 5.5
24 Hours at 25°C/77°F 0.1 - 0.2
2 Hours at 100°C/212°F 1.2 - 1.3

Physical properties shown are based upon the following cure schedule: 24 Hours at 77°F + 2 Hours at 250°F

The information herein in general information designed to assist customers in determining whether our products are suitable for their applications. Our products are intended for sale to industrial and commercial customers. We require customers to inspect and test our products before use and to satisfy themselves as to contents and suitability for their specific applications.

This resin is filled by weight not volume.
Net Weight
8.75lbs/3969g = aprox 1 Gallon

This hardener is filled by weight not volume.
Net Weight
4.02lbs/1823g = aprox 1/2 Gallon

The item has a shelf life of approximately one year. To ensure quality results and proper curing, please make sure to use the resin shortly after purchase.

*** Cold Weather Warning ***

If your epoxy arrives cold during shipment is must be allowed to acclimate to at least 75° F before using. Mixing this product below 75°F will increase the potential for under-mixed epoxy which will create wet or sticky areas on your surface. Cold temperatures will also trap more very tiny air bubbles during the mixing which cannot always be removed with the torch/heat gun. In addition applying the mixed epoxy in temps below 70° F will drastically extend cure times. To warm the epoxy quickly we recommend using either a heat lamp, an electric heater or placing the closed bottles of epoxy in a tub of warm water for 30 minutes. Getting the epoxy too hot will result in a faster reaction time, so pay careful attention to what you're doing.

*** Cold Weather Warning ***

MSDSThin Epoxy Resin SDS

MSDS2:1 Hardener SDS

PDF Epoxy Mixing Guide