Composite Envisions Medium Infusion Hardener

SKU: 2429

$43.44$319.88

Clear

    Add to Compare

    Description

    Medium Infusion Epoxy is a two-component, very low viscosity system developed specifically for use in resin infusion and VARTM processes. Medium Infusion Epoxy was formulated to provide for rapid saturation of carbon fiber laminate, fiberglass and Kevlar while also allowing for maximum open time. Processability parameters are enhanced due to Medium Infusion Epoxy’s low mixed viscosity and wet-out potential. This system is not designed to be used in open mold applications.

    Handling Properties
    RESIN VISCOSITY, cP 1,044 ASTM D 2196
    RESIN DENSITY, lb./gal 9.49 ASTM D 792
    HARDENER VISCOSITY, cP 39 ASTM D 2196
    HARDENER DENSITY, lb./gal 7.78 ASTM D 792
    COLOR Clear
    DENSITY, lb./gal 9.02 ASTM D 792
    MIX RATIO, pbv (pbw) 3/1 (3.65/1)
    MIXED VISCOSITY, cP 291 ASTM D 2196
    GEL TIME (200g), min 160 ASTM D 2471
    WORKING TIME*, min 120

    *The working time varies according to the temperature of the air, the epoxy and the surface to which it is applied.

    Note: Above viscosities/densities measured @ 77°F.

    Physical Properties: 
    TENSILE STRENGTH, psi 10,300 ASTM D 638
    TENSILE MODULUS, psi 294,000 ASTM D 638
    ELONGATION @ BREAK, % 3.16 ASTM D 638
    COMPRESSIVE STRENGTH, psi 13,700 ASTM D 695
    COMPRESSIVE MODULUS, psi 263,000 ASTM D 695
    FLEXURAL STRENGTH, psi 17,300 ASTM D 790
    FLEXURAL MODULUS, psi 1,063,000 ASTM D 790
    HARDNESS, Shore D 88D ASTM D 2240

    Cure Cycle: 24 hours @ Room Temperature + 8 hours @ 180°F. Test specimens for above were neat epoxy (without fiber reinforcement).

    The storage temperature of Medium Infusion Epoxy will greatly affect the ease of mixing, application and curing time. For best results, Medium Infusion Epoxy should be stored at (60-80 °F or 16-27 °C) for at least 24 hours before use. Mix RESIN WITH (hardener) for 3 minutes using a Jiffy Mixer and a slow speed drill. Mix at slow speed (less than 500 rpm) to avoid air entrapment. When adding part B to part A, be sure to scrape the sides of the hardener (part B) container in order to remove all of the hardener. This is essential to maintain proper mix ratio. DO NOT mix more material than can be used within the stated working time. REMEMBER – you will have less working time at higher temperatures

    SAFETY PRECAUTIONS

    Avoid breathing of vapors. Forced local exhaust is recommended to effectively minimize exposure. NIOSH approved, organic vapor respirators and forced exhaust are recommended in confined areas, or when conditions (such as heated polymers, sanding) may cause high vapor concentrations. DO NOT WELD ON, BURN OR TORCH ON OR NEAR, ANY EPOXY MATERIAL. HAZARDOUS VAPOR IS RELEASED WHEN AN EPOXY IS BURNED.

    0/5 (0 Reviews)

    Additional information

    Brand

    Size

    ,

    Color

    Cure Time

    Used For/Type

    Pot Life

    Max Service Temperature

    Product Type (i.e. resin, hardener, etc)

    Shelf Life

    UV Protection?

    Viscosity

    Filler

    Possible Amine Blush?

    Shipping

    Reviews

    There are no reviews yet.

    Only logged in customers who have purchased this product may leave a review.

    SDS/TDS/Guides

    Infusion Epoxy Medium Hardener SDS

    Infusion Epoxy Resin / Medium Hardener TDS

    Epoxy Mixing Guide

    Compare Products