Carbon Fiber Part Wrapping Kit w Clear Epoxy - Choose Your Fabric

Ground Only

Selecting materials for wrapping/covering existing parts in carbon fiber just got easier with our pre-made kits. These kits include all of the materials you need to cover your parts in carbon fiber to give them that desired look. You can also use these kits to produce parts entirely from carbon fiber as well.

The kits are available in three different sizes with the following Carbon Fiber options:

Each kit also includes the below materials.

LineItem  Model Description Small Kit Medium Kit Large Kit 
 1 Varies Carbon Fiber Fabric Choice Yard (50"x36") 2 Yards (50"x72") 3 Yards (50"x108")
 2 1159-Gallon|1160-1/2_Gallon-Kit 2:1 Thin Epoxy Resin with Hardener 48oz Kit (1 Qt epoxy with 16oz hardener) 96oz Kit (1/2 Gal epoxy with 1 Qt hardener) 144oz (3 Qt epoxy with 1.5 Qt hardener)
 3 667 Black Pigment for Basecoat 1oz 1oz 1oz
 4 496 Partall Paste #2 Wax 4oz 4oz 4oz
 5 4597 Latex Gloves (One Size Fits All) 8 pair 8 pair 8 pair
 6 966 4" Spreader 3 pcs 3 pcs 3 pcs
 7 402 Measuring Cup 2 pcs 2 pcs 2 pcs
 8 1143 Epoxy Mixing Tub with Measurements 16oz 3 pcs 3 pcs 3 pcs
 9 1997-1" Bristle Brush 1" 3 pcs 3 pcs 3 pcs
 10 952 Mixing Sticks 6 pcs 6 pcs 6 pcs
 11   Basic Instruction Guide 1 pc 1 pc 1 pc

All of these items in the kit are available for purchase individually in our store. If you run out of a certain material all items in this can can be purchased separately.

This resin uses a 2:1 hardener. Mixing 2 parts epoxy to 1 part hardener will give you the appropriate final mixture.

The 2:1 hardener has a pot life of 35-40 minutes at 80° F, set time of 5-6 hours and a drying time of 24-48 hours. This epoxy is NON-blushing.

This is considered to be a slow hardener, Our 3:1 and 4:1 hardener epoxies will cure much faster. However this 2:1 hardener will provide you with the maximum working time possible and should not be used in temps under 70° F unless a very long curing time is needed.   Slow hardener should be used at temperatures above 80° F for optimal overnight curing.


****************** Cold Weather Warning ***************

If your epoxy arrives cold during shipment is must be allowed to acclimate to at least 75° F before using. Mixing this product below 75°F will increase the potential for under-mixed epoxy which will create wet or sticky areas on your surface. Cold temperatures will also trap more very tiny air bubbles during the mixing which cannot always be removed with the torch/heat gun. In addition applying the mixed epoxy in temps below 70 degrees F will drastically extend cure times. To warm the epoxy quickly we recommend using either a heat lamp, an electric heater or placing the closed bottles of epoxy in a tub of warm water for 30 minutes. Getting the epoxy too hot will result in a faster reaction time, so pay careful attention to what you're doing.

****************** Cold Weather Warning ***************

Click on the link below for the Instruction Guide to Part Wrapping.

PDFPart Wrapping Kit Instructions

PDF Epoxy Mixing Guide

We also have an instructional video available for separate purchase to help guide you through the part wrapping process.

video Secrets of the Overlay Instructional Video

4597 Latex Gloves (One Size Fits All) 8 pair 8 pair 8 pair