null

Carbon Fiber Fabric Biaxial +45/-45 Degree 12k 50"/127cm 11.8oz/400gsm H2550 Fiber DISCOUNTED REMNANTS

Model:
F-1989=REM
Unit of Measure:
Linear Yard
Tow Size:
12k
$95.97
Quantity Buy 5 - 9 Buy 10 - 24 Buy 25 - 49 Buy 50 - 99 Buy 100 or above
Per Linear Yard $ 91.17 $ 89.25 $ 86.37 $ 84.45 $ 81.57
Bulk Pricing
Qauntity
Per Linear Yard
Buy 5 - 9
Buy 10 - 24
Buy 25 - 49
Buy 50 - 99
Buy 100 or above
$ 91.17
$ 89.25
$ 86.37
$ 84.45
$ 81.57

Biaxial +45/-45 Degree Carbon Fiber Fabric/Cloth 50" 12k 400gsm. This material is Hyosung H2550 Fiber. This fabric has a width of 50", tow size of 12k and is woven in a biaxial +45/-45 weave. We would not recommend using this fabric for the visual or cosmetic layer of a part, however it will work great for adding bulk to a part especially at this price.

To harden the raw fabric into a usable form, you will need the appropriate resin or epoxy for your project.

 

 We have most of our material available for purchase in sample swatch books per fabric category. Samples of our fabrics can be purchased by Clicking this Link.

First Quality Remnants:

                First Quality Fabric Remnant Rolls are short rolls of fabric, which have no defects in them.  These remnant rolls are either left over fabric from the end of a roll, or sections of fabric which were cut at the wrong length for a specific order.  So instead of discarding the short roll, we package it up and sell it as a First Quality Remnant Roll.  These First Quality Remnant Rolls are sold at 20% off of the retail price of that fabric.

Second Quality Remnants:

                Second Quality Fabric Remnant Rolls are short rolls of fabric, which have a defect in the woven fabric in them.  These remnant rolls are cut out of the standard fabrics we sell, but from sections of the rolls that have some defects in them.  These defects make them not good to use if you want to make cosmetic parts, which have perfect woven fabric in them, but can be used as the inner layers of your parts, or if you are making small parts and can cut around the defects.  These Second Quality Remnant Rolls are sold at 25% off of the retail price of that fabric.  

                All remnant rolls are rounded DOWN to the nearest ½ yard. So a remnant listed as 0.5 yards may actually be between 18” and 35” in length and a remnant listed at 2.0 yards may actually be between 72” and 89” in length.

Product Specs  
Unit of Measure Piece
Material Warp Carbon Fiber Hyosung H2550
Material Weft Carbon Fiber Hyosung H2550
Weave Biaxial +45/-45
Tow Size 12k
Weight 11.8oz / 400gsm
Width 50" / 127cm
Resin Consumption @ 45% Resin to Fabric by Weight 9.65opsy / 324.44gsm

The resin consumption provided is for the approximate amount of resin by weight, contained in the final part after processing by vacuum infusion. This does not account for the resin used in the flow lines and consumables such as flow media or breather cloth. Wet-layup by hand will also have a higher resin consumption in the final part and is dependent upon users techniques. Vacuum bagging a wet layup will improve the resin content. Too much resin will cause a weaker part, NOT stronger. Average rule of thumb is around 45% (+/- a couple percent). To calculate actual resin % in your part a burn test is used. For example you have a part weighing 100 grams, you would burn off the resin which would leave the fiber behind. You should have 55 grams of fiber left when your process is working correctly. Due to the variables in processing it is hard to give an accurate amount of resin needed to purchase for making your part. However you will have waste no matter what method is used. A suggested ratio is about 1-1.5lbs of resin per lb of fabric purchased.

 

TDSH2550 TDS